New construction HVAC, Castle Pines
HVAC for new buildings in Castle Pines
Bid-ready HVAC pricing for Castle Pines general contractors, developers and custom home builders.
- Insured
- EPA-certified technicians
- Design-build and plan-and-spec
- 24/7 emergency response
New construction in Castle Pines keeps moving. The Canyons is adding new homes and commercial space on the east side of I-25, and custom rebuilds continue inside the Village. We bring loads, equipment selection, submittals and clean rough-in to every job, and we flag document conflicts early rather than at change order time.
Castle Pines project spec sheet
| County | Douglas County |
|---|---|
| Elevation | About 6,200 to 6,400 feet |
| Key areas | The Village at Castle Pines, The Canyons, the Castle Pines Parkway commercial area and homes near Daniels Park |
| Project types | Commercial, mixed-use, multifamily, townhomes, custom homes |
| Delivery | Design-build, design-assist, plan-and-spec |
| Systems | RTUs, split systems, VRF, heat pumps, boilers, ERV and DOAS |
The Castle Pines development picture
Commercial property in Castle Pines is limited and centered on the Castle Pines Parkway retail and service area, so most of our work here is large residential. Active areas include The Village at Castle Pines, The Canyons, the Castle Pines Parkway commercial area and homes near Daniels Park.
Every new building in Castle Pines has to pass inspection, satisfy current energy codes and work for its owner for decades. The Village at Castle Pines holds some of the largest custom homes in the metro, often with hydronic radiant heat, snowmelt and multiple air handlers. We size systems from loads, not rules of thumb, and coordinate early with the framer, plumber and electrician.
What we deliver on Castle Pines new builds
We build repeatable typical details for multifamily, protect equipment space early on custom homes, and deliver startup reports and closeout documents at turnover.
- Closeout documents and training
- Multifamily typical unit details
- Load calculations and system selection
- Duct design and equipment layout
- Submittals and RFIs
- Sleeves and rough-in
- Gas piping and venting coordination
- Ventilation and exhaust
Process
- Survey. Existing conditions or construction documents reviewed in detail
- Price. Scope, options and exclusions in writing, so the number holds
- Install. Scheduled work windows, protected finishes and clean sites
- Commission. Startup, balancing, controls and training before turnover
Local conditions in Castle Pines
- Large custom homes often have multiple systems, zoning and sometimes hydronic or radiant heat.
- Exposed ridges bring wind, drifting snow and hail that wear on outdoor equipment.
- Elevation above 6,000 feet makes altitude-correct furnace setup essential.
At about 6,200 to 6,400 feet, Castle Pines equipment works in thin air, intense sun and hail. We select capacity with altitude correction, set gas equipment to the manufacturer's elevation guidance and plan outdoor equipment for hail exposure.
We also deliver new construction HVAC in nearby Castle Rock, Lone Tree, Highlands Ranch and Parker. For the full overview, including our pricing approach, process and common questions, see new construction HVAC in Denver.
Start a new construction HVAC project in Castle Pines
Send drawings, a scope or a site address in Castle Pines. We reply with next steps, the information we need and a time for a plan review or site walk, and the scope is in writing before anything is scheduled.
Castle Pines new construction HVAC questions
Do you build around The Village at Castle Pines and The Canyons?
Yes. We price and build mechanical packages across Castle Pines, including The Village at Castle Pines, The Canyons, the Castle Pines Parkway commercial area and homes near Daniels Park.
Do you price Castle Pines projects from plans?
Yes. Send drawings, specification and schedule for your Castle Pines project and we return a written bid with scope, clarifications and exclusions.
When should we bring you in?
At schematic design for design-build, so equipment space and duct routes are protected, or at bid time for plan-and-spec work.
Do you build multifamily?
Yes. We set typical unit details with the GC early, then hold them consistently from rough-in to trim so inspections stay predictable on every floor.
Do you handle inspections?
Yes. We coordinate rough and final mechanical inspections and correct any items quickly so the schedule keeps moving.