Custom home HVAC, Aurora
Aurora luxury custom home HVAC
Multi-zone forced air, hydronic radiant, humidification, fresh air and smart controls for Aurora custom homes.
- Insured
- EPA-certified technicians
- Design-build and plan-and-spec
- 24/7 emergency response
A custom home in Aurora deserves a mechanical system designed for that house. Southeast Aurora communities like Blackstone and Saddle Rock include large homes where zoning and full-system replacement are common projects. We start with room-by-room loads and build the zoning, equipment rooms and controls around the architecture.
Building custom in Aurora
Everything from 1950s and 1960s homes in north Aurora to large newer homes in southeast Aurora's golf and master-planned communities. Typical locations include Southlands, Saddle Rock and Tallyn's Reach.
Owners building in Aurora expect every room to feel the same, summer and winter. Aurora spans hospital and research buildings at Anschutz, regional retail at Southlands and Aurora Town Center, and a large and growing base of warehouses, flex and hospitality along E-470. We design the system room by room and commission every zone before move-in.
Aurora project spec sheet
| Heating | Modulating furnaces, heat pumps, condensing boilers, radiant floors |
|---|---|
| Comfort | Humidification, fresh air, high-MERV filtration, zoning |
| Pricing | Per plans after review |
| County | Arapahoe, Adams and Douglas Counties |
| Elevation | About 5,400 to 5,500 feet |
| Key areas | The Anschutz Medical Campus and Fitzsimons area, Southlands, the Gaylord Rockies and E-470 corridor and the Aurora Town Center area |
How we design Aurora custom homes
Equipment is selected for altitude and placed for quiet operation and service access. We plan electrical and piping so a future geothermal or heat pump conversion stays simple.
- ERV or HRV fresh air
- Smart controls and home automation integration
- Geothermal-ready layout
- Startup, balancing and owner training
- Quiet equipment placement
- Room-by-room load calculation
- Zoning plan by level, wing and exposure
- Hydronic radiant floors
Process
- Walk or review. A site walk or plan review to understand the building, access and goals
- Proposal. A written scope with equipment, schedule, exclusions and price
- Build. Installation coordinated with your team, the other trades and the building
- Close out. Startup, documentation and a walkthrough with the owner or manager
Site factors in Aurora
- Older north Aurora homes may still have original ductwork and furnaces at the end of their life.
- Southeast communities like Blackstone and Saddle Rock have larger homes that benefit from zoning and high-efficiency equipment.
- Open eastern plains exposure means wind and hail on outdoor units.
At about 5,400 to 5,500 feet, Aurora equipment works in thin air, intense sun and hail. We select capacity with altitude correction, set gas equipment to the manufacturer's elevation guidance and plan outdoor equipment for hail exposure.
We also deliver custom home HVAC in nearby Commerce City, Centennial, Parker and Cherry Creek. For the full overview, including our pricing approach, process and common questions, see custom home HVAC in Denver.
Start a custom home HVAC project in Aurora
Send drawings, a scope or a site address in Aurora. We reply with next steps, the information we need and a time for a plan review or site walk, and the scope is in writing before anything is scheduled.
Aurora custom home HVAC questions
When should a builder bring you in?
During design development, before framing plans are final. That protects space for equipment rooms, chases, returns and duct routes, and avoids compromises later.
Do you build custom homes in Southlands?
Yes. We work on custom homes across Aurora, including Southlands, Saddle Rock, Tallyn's Reach, Blackstone and older neighborhoods in north Aurora.
Do you install radiant and snowmelt?
Yes. We design and install hydronic radiant floors and snowmelt for drives, walks and terraces, typically served by high-efficiency condensing boilers.
Does Aurora's elevation change the design?
Yes. At about 5,400 to 5,500 feet, gas equipment needs high-altitude setup and cooling capacity drops, so equipment is selected with altitude correction.
How many zones does a custom home need?
It depends on the layout. We base zoning on room-by-room loads, usually separating levels, wings, guest quarters and rooms with large west-facing glass.