New construction HVAC, Brighton
Brighton new construction mechanical
Commercial, multifamily and custom home mechanical packages in Brighton, delivered design-build or bid from your drawings.
- Insured
- EPA-certified technicians
- Design-build and plan-and-spec
- 24/7 emergency response
New construction in Brighton keeps moving. Brighton keeps growing with new subdivisions, multifamily and commercial pads, making it a steady new construction market on the northeast edge of the metro. We bring loads, equipment selection, submittals and clean rough-in to every job, and we flag document conflicts early rather than at change order time.
Brighton project spec sheet
| Project types | Commercial, mixed-use, multifamily, townhomes, custom homes |
|---|---|
| Delivery | Design-build, design-assist, plan-and-spec |
| Systems | RTUs, split systems, VRF, heat pumps, boilers, ERV and DOAS |
| County | Adams and Weld Counties |
| Elevation | About 4,980 feet |
| Key areas | Historic downtown Brighton, the Prairie Center retail area, the I-76 and US 85 corridors and the Bromley Lane corridor |
The Brighton development picture
Brighton's commercial base mixes downtown storefronts and civic buildings, regional retail around Prairie Center and industrial, agricultural and distribution buildings along I-76 and US 85. Active areas include historic downtown Brighton, the Prairie Center retail area, the I-76 and US 85 corridors and the Bromley Lane corridor.
Brighton is the Adams County seat, a former agricultural town on the northeast edge of the metro that has grown quickly along I-76 and US 85. New buildings here face Front Range sun, hail, dry air and subzero cold snaps, so equipment selection, ventilation and freeze protection are designed in from the start rather than fixed after occupancy.
What we deliver on Brighton new builds
In design-build we run loads, select systems and lay out ductwork, coordinating with a mechanical engineer of record when stamped drawings are required. In plan-and-spec we price exactly what the documents show.
- Duct design and equipment layout
- Submittals and RFIs
- Sleeves and rough-in
- Gas piping and venting coordination
- Ventilation and exhaust
- Rough and final inspections
- Startup and balancing coordination
- Closeout documents and training
Process
- Walk or review. A site walk or plan review to understand the building, access and goals
- Proposal. A written scope with equipment, schedule, exclusions and price
- Build. Installation coordinated with your team, the other trades and the building
- Close out. Startup, documentation and a walkthrough with the owner or manager
Site factors in Brighton
- Large newer subdivisions mean many builder-grade systems are now reaching their first replacement window.
- Industrial, agricultural and distribution buildings along I-76 and US 85 depend on rooftop units and unit heaters.
- Open plains exposure brings strong wind and hail to outdoor equipment.
Brighton sits at about 4,980 feet. At that elevation gas equipment needs the manufacturer's high-altitude setup and cooling capacity is lower than sea-level ratings suggest, so we select and set up equipment for the actual site.
We also deliver new construction HVAC in nearby Thornton, Commerce City, Northglenn and Erie. For the full overview, including our pricing approach, process and common questions, see new construction HVAC in Denver.
Start a new construction HVAC project in Brighton
Send drawings, a scope or a site address in Brighton. We reply with next steps, the information we need and a time for a plan review or site walk, and the scope is in writing before anything is scheduled.
Brighton new construction HVAC questions
Do you build around historic downtown Brighton and the Prairie Center retail area?
Yes. We price and build mechanical packages across Brighton, including historic downtown Brighton, the Prairie Center retail area, the I-76 and US 85 corridors and the Bromley Lane corridor.
Do you price Brighton projects from plans?
Yes. Send drawings, specification and schedule for your Brighton project and we return a written bid with scope, clarifications and exclusions.
When should we bring you in?
At schematic design for design-build, so equipment space and duct routes are protected, or at bid time for plan-and-spec work.
Do you build multifamily?
Yes. We set typical unit details with the GC early, then hold them consistently from rough-in to trim so inspections stay predictable on every floor.
Do you handle inspections?
Yes. We coordinate rough and final mechanical inspections and correct any items quickly so the schedule keeps moving.